Forum Home | Log in | Signup | My Page | Rules | FAQ | Boards | Members | Search
« F@H Home | Email msg. | Reply to msg. | Post new | Board info. Previous | Home | Next

Re: Help!/ SUN This should fix it

By: micro in F@H | Recommend this post (0)
Sun, 27 Jan 13 5:33 PM | 38 view(s)
Boardmark this board | Folding at Home 		Msg. 01785 of 02753
(This msg. is a reply to 01782 by new_sun_rising)
Jump:
Jump to board:
Jump to msg. #

check this out and see if it helps.

http://www.asknetinfo.com/resolved-blue-screen-error-stop-0x0000007b-0xf78d2524-0xc0000034-0x00000000-0x00000000.html

Resolved Blue screen error
“STOP: 0x0000007B (0xF78D2524, 0xC0000034, 0×00000000, 0×00000000)”

On a Laptop “Lenovo IdeaPad Y550″ i got a Blue Screen error “STOP: 0x0000007B (0xF78D2524, 0xC0000034, 0×00000000, 0×00000000)”. It started rebooting itself while loading its windows 7. I tried to recover Windows 7 using its own recovery tool but failed. It was unable to read the disk.
I tired to install fresh Windows XP but after loading initial install files it reboots.

While searching the solution for this issue i found following,

1. On start up, press F2 to enter BIOS

2. Expand the “Drives” section

3. Go to “SATA Operation”

4. Change this from “RAID Auto/AHCI” to “RAID Auto/ATA”

It was saying to change the Drive operation mode, looks strange first but i was decided to go with it and went to BIOS setup. On Lenovo IdeaPad Y550 the Drives configuration is different.
I used the followng steps,

1. On start up, pressed F2 to enter BIOS setup

2. Went to “Configuration” tab

3. Located “SATA Mode Selection”

4. Changed the mode from AHCI to IDE

5. Saved the Configuration and rebooted.

This resolved the Blue screen error and i was able to run the fresh install.


 - - - - -
View Replies (1) »



» You can also:
- - - - -
The above is a reply to the following message:
Help!
By: new_sun_rising in F@H
Sun, 27 Jan 13 5:43 AM 		Msg. 01782 of 02753

Guys,

Hollywood is down. I got the new motherboard installed, new CPU installed, new fan installed, new hard drive installed and I think I got all the case connections installed.

Tried firing her up and she starts up. Insert the installation disk for Windows, she starts through everything, but right after it tells me Windows is starting up, a blue screen comes up that says "A problem has been detected and Windows has been shut down to protect your system" Says is that's the first time you've seen that screen, to try a restart. Restart results in the same situation.

It gives some numbers at the bottom of that screen, but I have no idea what they mean or where to find what they mean?

Stop: 0x0000007B (0xf78D2524, 0x00000034, 0x00000000, 0x00000000)

Any suggestions out there? :-(

I did not install the video card yet, past experience has told me to take this one step at a time and try it. Then another step and try it - so I've just installed enough to get her running and try her.

I tried it both with the new Windows XP disk that I got as well as with the old one that was loaded on her before this tear down. They both get to the same point and give me the same message


Sun :-)

« F@H Home | Email msg. | Reply to msg. | Post new | Board info. Previous | Home | Next